Sunbrella® or Outdura® 9.25oz/sq.yd Premium 100% solution-dyed Marine Acrylic,
Sun-DURA® 7oz/sq.yd solution-dyed Polyester,
Poly-Guard® 8oz/sq.yd marine grade Polyester.
PADS with SNAPS sewn into inside of cover (2 on most, 1 on smaller covers) for Support Poles (below),
TIE-DOWN-LOOPS (every 3-4 feet) double sewn in an offset "V" for strength and less strap twisting,
TRAILERABLE when cinched tightly and tied down with Tie Down Straps (below) to V loops along rub rail,
Durable reinforcements SEWN in (not glued) at all major wear points for extra durability,
1/4" Draw Rope sewn into hem to secure cover tightly under rub rail,
Motor cover included on most outboard models.
Size/Fit: Fits 2010-2014 Tahoe® Q5i WithOut Tower. I/O,
Custom Fit and GUARANTEED TO FIT the specific year/make/model boat setup described here,
Will NOT fit other years/makes/models (no returns),
Must remove Pedestal Seats from fishing boats,
Fits Standard Integrated Fiberglass Swim Platform (as shown at right),
Does NOT FIT THE FOLLOWING UNLESS SPECIFICALLY STATED IN BOAT DESCRIPTION:
Other boat model or years,
Wakeboard Tower, Radar Arch, Ski Tow Pylon,
Folded or Upright Bimini-Top, Camper-Top, T-Top, Hard-Top,
Wooden, Poly or Add-On Swim Platform,
Bow or Stern Mounted Trolling Motor,
Raised or protruding antennas, brackets, winches, mirrors, rod holders, etc.,
Will NOT fit ANY NON-Factory-Installed Arch, Tops or Wakeboard Tower because it may be installed in a different location.
Cover is NOT intended for use on a LIFT, as it is difficult (or impossible) to pull the cover back over the transom properly,
Cover is NOT intended for In-Water use (like a Mooring Cover). It is a designed for use on a trailer or dry stack (or float dock or lift if it can be pulled tightly enough at the rear). It does NOT have openings for Mooring Lines, and may hang in the water.,
Heavy duty 1/4-inch Cinch Rope (not elastic) encased in hem cinches tightly around the boat below the rub rail at the following Cinch Locations:
Tower: If the description states that it fits a Factory Tower, then it cinches on the sides at the tower leg cutouts,
Bimini: If the description states that it fits a Bimini-Top, then it will cinch on the sides,
NO Tower or Bimini: If the boat (and cover) does NOT have an OEM Tower or Bimini then it will cinch at the center of the transom under the rub rail (or under swim platform, if so equipped).
Installation: Cover is rolled and packaged with the bow end of the cover to the outside. The tag on the bow end is sewn into the inside hem of the cover. To cover your boat, start at the bow and follow these instructions: Carver® Custom-Fit™ Boat-Cover Installation Instructions.
Lead-Time (Estimated): Lead time est. for tops/covers is 9-11 weeks, 3 days for poles/straps from order finalization (as of 12/8/20)
$39.39 Shipping to Continental US48
$177.59 Shipping to HAWAII
$128.02 Shipping to CANADIAN PROVINCES
$FF Shipping to EUROPE
$FF Shipping to AUSTRALIA
Shipping Notes: Signature required for delivery on orders over $500. Can NOT ship to Post Office (PO) Box. Can NOT change your address after order is placed. Buyer is responsible for all Taxes, Duties and Tariffs imposed by local governments. Use a US48 Based (in Florida, New Jersey or Oregon for example) Freight Forwarder to ship outside US. Check shipment for damage upon receipt and file claim with shipper.
RNR-Marine® has the lowest prices on the Internet for Carver® Custom-Fit Boat Covers!
We have Carver® Trailerable Custom-Fit Boat Covers for (20) different TAHOE® boat models, including the boat-cover pattern specifically for 2010-2014 TAHOE® Q5I WithOut TOWER., I/O (sterndrive) (NO Raised Bimini)
Not what you need? Try
Custom-Fit™ boat covers manufactured in the USA by Carver® for 35 years:
https://www.youtube.com/watch?v=1W4dCGZxxNw&rel=0