nmf Carver® 71018A Styled-To-Fit™ Trailerable Boat Cover for Pioneer® 180 Islander O/B, With Bimini Folded Forward (2018-2021) from RNR-Marine.com™
Purchase Carver® 71018A Styled-To-Fit™ Trailerable Boat Cover part number [71018A] for Pioneer® 180 Islander O/B, With Bimini Folded Forward (2018-2021)
Boat Cover CSF Model 710xx, Boat Sketch.
Boat Cover CSF Model 710xx, Boat Sketch with Cover.
Images (random) of Boat-Cover-CSF-Model (click images to enlarge).
Notes:Styled-To-Fit™ Boat Covers, manufactured in the SC, USA for 45 years by Carver® are GUARANTEED TO FIT the specific year/make/model boat per https://dealerguide.CarverCovers.com/mmy/boat,
Solution-Dyed Fabrics (the dye goes all the way through the threads rather than just on the surface, to reduce fading):
Sunbrella® or Outdura® 9.25oz/sq.yd Premium 100% solution-dyed marine grade Acrylic,
Sun-DURA® heavy duty, 600-denier, 7.6oz/sq.yd solution dyed marine grade Polyester,
Join seams are folded four-ply (no raw edges) and sewn with double-stitches using weather resistant anti-wick thread for added strength and durability,
"V" Loops (every 3-4 feet) double sewn in an offset "V" for strength and less strap twisting to attach Tie-Downs or Sand-Bags (sold below) along bottom edge of cover,
Can be used IN-WATER or on a drive-on FLOAT as a MOORING COVER with Sand Bags (below),
TRAILERABLE when properly installed and tied down with INCLUDED: FREE 12 (or 6 on smaller covers) TIE-DOWN STRAPS (NOT Bungee cords),
1/4" Stretch Cord in hem (No Snaps) to pull cover tight under rub rail,
MOTOR COVER sewn into outboard (O/B) model boat covers (some use a separate motor cover).
Bay style Center Console (up to 56 inch) fishing boat (shallow draft hull); O/B,
NO T-Top; Bow Rails up to 8 inches tall; No or Lowered Bimini; Buy Longer Cover for JACK PLATE; No Poling Platform; Motor Cover attached
Cover is GUARANTEED TO FIT this specific year/make/model boat setup,
Bimini-Tops must be lowered and stored flat or removed (unless stated otherwise),
Pedestal Seats must be removed or lowered,
Does NOT FIT THE FOLLOWING UNLESS SPECIFICALLY STATED IN BOAT DESCRIPTION ABOVE: • Other boat models or years (it MAY fit other boats, but we cannot guarantee fit), • Wakeboard Tower, • Folded or Upright Bimini-Top, • Radar Arch, • Camper-Top, • T-Top, • Hard-Top, • Ski Tow Pylon, • Non-Integrated Swim Platform, • Bow or Stern Mounted Trolling Motor, • Raised or protruding antennas, brackets, winches, mirrors, rod holders, etc.,
Will NOT fit ANY NON-Factory-Installed Arch, Top or Tower because it may be installed in a different location,
NOT intended for use on a LIFT, as it is difficult (or impossible) to pull the cover back over the transom properly,
Does NOT have or use Snaps like a factory original Bow, Cockpit or Playpen Cover,
Ships in a 12 x 12 x 19 box weighing approximately the boat's length (E.g.: 22' boat = 22# cover).
Warranty: The materials and workmanship are guaranteed by Carver® to be free of defects at time of manufacture and are covered by Carver's® https://www.carvercovers.com/about-carver/product-warranty-information/ limited warranties: Sunbrella®/Outdura®: 10 years, Sun-Dura™: 7 years. (Note: The use of Bungee Cords instead of Tie-Down Straps on Boat-Covers will void the warranty).
Installation: Cover is rolled and packaged with the bow end of the cover to the outside. The tag on the bow end is sewn into the inside hem of the cover. Start at the bow and follow these instructions: Carver® Boat Cover Installation Instructions.
Lead-Time (Estimated): Lead time est: tops/covers: 3-10 biz days , 3-4 biz days for poles/straps after order finalization as of 1/12/24.
Shipping Notes: Signature required for delivery on orders over $500. Can NOT ship to Post Office (PO) Box. Can NOT change your address after order is placed. Buyer is responsible for all Taxes, Duties and Tariffs imposed by local governments. Use a US48 Based (in Florida, New Jersey or Oregon for example) Freight Forwarder to ship outside US. Check shipment for damage upon receipt and file claim with shipper.
We have Carver® Styled-To-Fit™ Boat Covers for (20) different PIONEER® boat models,
Oops, there was a search error or NO Carver® Styled-To-Fit™ Boat-Covers found for [PIONEER] [180 Islander O/B, With Bimini Folded Forward|2018-2021] (err3)
No problem...
Please select your boat model and options from our complete list of Carver® Styled-To-Fit™ Boat-Covers: