nmf Carver® 74203A Styled-To-Fit™ Boat Cover for Rebel® V-160 (1995-1995) from RNR-Marine.com™

Carver® 74203A Styled-To-Fit™ Boat Cover
part number [74203A]
for Rebel® V-160 (1995-1995)

Boat-Cover-CSF-Model™Carver(r) 742xx series Styled-To Fit(tm) boat cover (for Open Flat Bottom Jon boat; O/B (over 13 foot) or no Motor (less than 13 foot)) provides a GUARANTEED Fit
Boat Cover CSF Model 74200 74205, Boat Sketch.
Boat-Cover-CSF-Model™Carver(r) 742xx series Styled-To Fit(tm) boat cover (for Open Flat Bottom Jon boat; O/B (over 13 foot) or no Motor (less than 13 foot)) provides a GUARANTEED Fit
Boat Cover CSF Model 74208 74212, Boat Sketch.
Images (random) of Boat-Cover-CSF-Model
(click images to enlarge).

RNR-Marine, Inc. ProductsNot what you need? Try

• Everything we have for Rebel 160s...
• We have Boat-Cover-CSF-Models for these boats.
  • Notes: Carver®Styled-To-Fit™ Boat Covers for over 25,000 specific boat models have been manufactured in the USA by Carver® Covers for 35 years:
    • GUARANTEED by Carver® TO FIT the specific year/make/model boat per https://dealerguide.CarverCovers.com/mmy/boat,
    • Fabric choices:Sunbrella® logo
      1. Sunbrella® or Outdura® 9.25oz/sq.yd Premium 100% solution-dyed Marine Acrylic,
      2. Sun-DURA® 7oz/sq.yd solution-dyed Polyester,
      3. Mossy Oak® Camo 8oz/sq.yd marine grade Polyester (fishing boats),
      4. Poly-Guard® 8oz/sq.yd marine grade Polyester.
    • Join seams are folded four-ply (no raw edges) and sewn with double-stitches using weather resistant anti-wick thread V-Loopsfor added strength and durability,
    • TRAILERABLE when properly installed and tied down with optional #61001 Tie-Down Straps (below, 2 sets for boats over 20 foot) connected to double "V" loops along bottom edges of the cover,
    • Tie-Down Loops (every 3-4 feet) double sewn in an offset "V" for strength and less strap twisting to attach Tie-Down Straps or Sand-Bags (below),
    • 1/4" Stretch Cord in hem to pull cover tight under rub rail,
    • MOTOR COVERS sewn into outboard (O/B) model boat covers (some have separate motor cover).

    Size/Fit: Fits 1995 Rebel® V-160,
    • Open Flat Bottom Jon boat; O/B (over 13 foot) or no Motor (less than 13 foot),
    • Bow Trolling Motor; No Console; No Bimini; Motor Cover attached on O/B models over 13 foot
    • Cover is GUARANTEED TO FIT this specific year/make/model boat setup,
    • Bimini-Tops must be lowered and stored flat or removed (unless stated otherwise),
    • Pedestal Seats must be removed or lowered,
    • Does NOT FIT THE FOLLOWING UNLESS SPECIFICALLY STATED IN BOAT DESCRIPTION: Other boat models or years (it MAY fit other boats, but we cannot guarantee fit), Wakeboard Tower, Folded or Upright Bimini-Top, Radar Arch, Camper-Top, T-Top, Hard-Top, Ski Tow Pylon, Non-Integrated Swim Platform, Bow or Stern Mounted Trolling Motor, Raised or protruding antennas, brackets, winches, mirrors, rod holders, etc.,
    • Will NOT fit ANY NON-Factory-Installed: Arch, Tops or Wakeboard Tower as it may have installed in a different location,
    • Cover is NOT intended for use on a LIFT, as it is difficult (or impossible) to pull the cover back over the transom properly,
    • Cover is NOT intended for In-Water use (like a Mooring Cover). It is a designed for use on a trailer or dry stack (or float dock or lift if it can be pulled tightly enough at the rear). It does NOT have openings for Mooring Lines, and may hang in the water..

  • Options: Tie-Downs Snap-Pole
    1. Carver® p/n 640xxA 30-inch Skirts protect colored sides/ graphics on boat from UV damage,
    2. Carver® p/n 61001 (12)each 8-foot Tie-Down Straps and Mesh Storage Bag (at right, 2 sets required for trailering boats over 20 foot),
    3. Carver® p/n 61010 Sand Bags (for dry stack or float docks),
    4. Carver® p/n 60000 Anodized Aluminum Support Pole snaps into adhesive pad(s) under cover (at right),
    5. Carver® p/n 60002 Vented Anodized Aluminum Support Pole,
    6. Carver® p/n 61050 Cover Reinforcement/Repair Kit for added padding (bow, pulpit, anchor roller) or to make repairs,
    7. Alternatives:

  • Warranty: The materials and workmanship of this products are guaranteed by Carver® to be free of defects at time of manufacture and are covered by the Carver® https://www.carvercovers.com/about-carver/product-warranty-information/ limited warranties: Sunbrella®: 10 years, Sun-Dura™: 7 years, Performance Polyguard®: 5 years. (Product warranties are listed on http://www.rnr-marine.com/Warranty.shtml).

  • Installation: Cover is rolled and packaged with the bow end of the cover to the outside.Carver Installation The tag on the bow end is sewn into the inside hem of the cover. Start at the bow and follow these instructions: Carver® Boat Cover Installation Instructions.

  • Maintenance and Care: Canvas Care and Maintenance

  • More Info: https://dealerguide.carvercovers.com/boat-styles/15
  • Reviews: Rated 4.5 / 5, based on 111 customer reviews   ★★★★✯

  • Video Link: YouTube®https://www.youtube.com/watch?v=1W4dCGZxxNw&rel=0
  • Made in USA.Made in USA

  • Lead-Time (Estimated): Lead time est: tops/covers: 4-7 weeks, 3-4 days for poles/straps from order finalization (as of 3/30/21)

  • Shipping Notes: Signature required for delivery on orders over $500. Can NOT ship to Post Office (PO) Box. Can NOT change your address after order is placed. Buyer is responsible for all Taxes, Duties and Tariffs imposed by local governments. Use a US48 Based (in Florida, New Jersey or Oregon for example) Freight Forwarder to ship outside US. Check shipment for damage upon receipt and file claim with shipper.
  • We have Carver® Styled-To-Fit™ Boat Covers for (44) different REBEL® boat models,

    Oops, there was a search error or NO Carver® Styled-To-Fit™ Boat-Covers found for [REBEL] [V-160|1995-1995] (err3)

    No problem...

  • Please select your boat model and options from our complete list of Carver® Styled-To-Fit™ Boat-Covers: ...