Notes: Exact-Fit™ Boat Covers have been manufactured in Texas, USA by Westland® for over 30 years:
GUARANTEED by Westland® TO FIT the specific year/make/model boat,
Three fabrics: Sunbrella® (most breathable and long-lasting), Sharkskin-Supreme™ and Sharkskin-Plus™,
TIE-DOWN-LOOPS (every 3-4 feet) double sewn in an offset "V" for strength and less twisting,
FREE: Twelve (12) durable black nylon webbing TIE-DOWN STRAPS included ($35 value) for boat trailer: (6)ea. 96-inch and (6)ea. 144-inch,
TRAILERABLE with reinforcements SEWN in (not glued) at all major wear points,
Two VENTS (behind windshield) to decrease moisture and mildew,
1/4" Rope (Not stretch cord) sewn into hem to pull tight below rub rail,
Some covers do not cover the outboard motor (if so equipped),
Support Poles offered below.
Size/Fit: Fits 1996-1997 BOSTON WHALER® OUTRAGE 19 III O/B,
Cover is Custom Fit and GUARANTEED TO FIT this specific year/make/model boat setup as described here,
Trailerable when tied down tightly with (12) Tie Down Straps (included) to V loops along rub rail AND Cinch Rope in hem fully tightened,
If so equipped:
Only fits Standard Integrated Fiberglass Swim Platform (molded into hull, shown at right),
Pedestal Seats MUST be REMOVED from FISHING BOATS,
Only fits factory installed Arches, Tops or Watersports Towers.
DOES NOT FIT THESE UNLESS SPECIFICALLY STATED ABOVE IN BOAT DESCRIPTION:
Watersport Tower, Folded or Upright Bimini, Convertible or Camper Top, Radar Arch, T-Top or Hard-Top,
Ski Tow Pylon,
Wooden, Poly or Bolt-On Swim Platform,
Raised or protruding antennas, brackets, winches, mirrors, rod holders, etc.
Will NOT fit ANY NON-OEM (After-Market) Arches, Tops or Watersport Towers,
Will NOT fit Owner-Installed or Dealer-Installed Arch, Top or Watersport Tower because it may be installed in a different location,
This cover is NOT intended for use on a LIFT, as it is difficult to pull the cover back over the transom properly.
This is a tight fitting Boat Cover designed for use on trailer or dry stack (or float dock or lift if it can be pulled tightly enough at the rear). It does NOT have openings for Mooring lines. Slit openings can be added by a local shop to make it a Mooring Cover for in-water use,
Cover NOT guaranteed to fit any other year/model, so this is your own risk,
Cinch Rope in hem fits tightly below the boat's rub rail at the following Cinch Locations:
Watersport Tower: If the description states it fits a Factory OEM Tower the it cinches on each side around the tower legs (with 2 included Quick Cinches) ,
Bimini: If the description states it fits a factory Bimini-Top, then it cinches on side,
NO Tower or Bimini: If the boat (and cover) does NOT have an Tower or Bimini then it cinches at the center of the transom under the rub rail (or under swim platform, if so equipped).
Shipping: 15-16 x 6-10 x 32-35 inch Box weighing 18 to 30lbs.
Shipping Notes: Signature required for delivery on orders over $500. Can NOT ship to Post Office (PO) Box. Can NOT change your address after order is placed. Buyer is responsible for all Taxes, Duties and Tariffs imposed by local governments. Use a US48 Based (in Florida, New Jersey or Oregon for example) Freight Forwarder to ship outside US. Check shipment for damage upon receipt and file claim with shipper.
RNR-Marine® has the lowest prices on the Internet for Westland® Exact-Fit Boat Covers!
We have Exact-Fit™ Trailerable Boat Covers for many different BOSTON WHALER® boat models, including the boat-cover pattern specifically for 1996-1997 BOSTON WHALER® OUTRAGE 19 III, O/B (outboard), NO Raised Bimini, does NOT cover O/B Motor boat with the following fabric options: