Wakeboard Tower Over The Tower Boat-Cover Deck Boat C

Wakeboard-Tower-Over-The-Tower-Boat-Cover-Deck-Boat-C™Completely covers DECK Boat and Wakeboard Tower (versus Bow, Cockpit and Mooring Covers that do not cover the hull AND tower)
Carver® Over The Tower, Deck Boat Cover, Starboard Front.
Wakeboard-Tower-Over-The-Tower-Boat-Cover-Deck-Boat-C™Completely covers DECK Boat and Wakeboard Tower (versus Bow, Cockpit and Mooring Covers that do not cover the hull AND tower)
Carver® Deck Boat with Tower.

(click image to enlarge)

RNR-Marine, Inc. ProductsNot what you need? Try

• Everything we have for Wakeboard-Tower-Over-The-Tower-Boat-Cover-Deck-Boat-Cs for these boats.
Completely covers DECK Boat and Wakeboard Tower (versus Bow, Cockpit and Mooring Covers that do not cover the hull AND tower):
  • Notes: USACarver Logo
    • For DECK BOATS with a WAKEBOARD TOWER (up to 68-inches tall),
    • Designed to protect the boat owner’s investment. Protects complete boat, wakrboard tower, speakers, wake board racks and swim platform (up to 30-inches long).
    • Designed for storage only (NOT trailerable) for boat lifts, dry stack or trailer storage,
    • Stretch-Cord in hem pulls tight around Hull (below Rub Rail) and Swim Patform,
    • Tie-Down StrapsV-LoopsHem/CordReinforced V-Loops every 3 to 4 feet along hem for tying cover down,
    • FREE Tie-Down Kit Included: (12) 8-foot black straps with buckles,
    • Ships in 21-inch x 17-inch x 15-inch box weighing 23-31 lbs.

  • Size/Fit:
    • The Carver® Over-Tower-Cover (OTC) is designed for DECK Boats with a WakeBoard Tower according to these measurements: see diagram at right (click to enlarge) ==>>
        OTC fit
      1. Boat's Center-Line-Length (CLL): from the tip of the Bow to back of the Transom OR integrated fiberglass Swim-Platform,
      2. BEAM: 102 inches boat width,
      3. Maximum WakeTower: from top of gunwales is 68 inches high,
      4. WakeTower Location: Top of the WakeTower not to exceed 24 inches behind (aft of) the wing (Back End of the Sides) of the windshield,
      5. Covers integrated (part of fiberglass boat) swim platform (measure CLL to back of intergrated swim platform if you have one)
    • Spin wakeboard racks in and fold or remove bimini top and all sharp objects on top of tower,
    • Use Tie-Down straps to V-Loops or Sand-Bags (not included) for dry stacks or lifts,
    • Does NOT fit V-Hull Tournament Ski Boats, Wide or Pickle-Fork Bow Ski Boats or V-Hull Runabouts,
    • This is NOT a factory OEM cover, so measure carefully because this cover is Made-To-Order and there are NO cancellations, refunds or returns.

  • Options:

  • Warranty: The materials and workmanship of this products are guaranteed by Carver® to be free of defects at time of manufacture and are covered by the Carver® https://www.carvercovers.com/about-carver/product-warranty-information/ limited warranties: Sunbrella®: 10 years, Sun-Dura™: 7 years, Performance Polyguard®: 5 years. The following will VOID warranty: 1) use of Bungee Cords instead of Tie-Down Straps, 2) use of Boat Cover In-Water (becuase the cover will stay wet). (Product warranties are listed on http://www.rnr-marine.com/Warranty.shtml).

  • Installation: InstructionsSee http://RNR-Marine.com/publications/Carver_Over-The-Tower_Boat-Cover_Instructions.pdf
    1. Add any padding needed for the windshield, wakeboard racks or any sharp areas that could damage the boat cover,
    2. Place the bow end of the rolled cover (the end with the tag) on the bow of your boat and unroll towards the stern or back, positioning it down the center of your boat as you roll,
    3. Slip the front of the cover over the bow and pull the cover open to the sides and over the tower as you work towards the stern of the boat,
    4. Adjust cover fit by pulling cover tight to eliminate sagging areas. These areas may collect standing water or snow and shorten the life of your cover,
    5. Using the reinforced loops, secure the cover to your trailer with the included tie-down kit.
    To remove the boat cover, fold it to the center from each side and roll it from back to front. This will make it easier to cover your boat again.

  • Maintenance and Care: Sunbrella® fabric Care and Maintenance. Allow the cover to dry thoroughly before folding for storage.

  • More Info: http://RNR-Marine.com/publications/Carver_Over-Tower-Cover_and_Wide-Over-Tower-Cover_Flyers.pdf

  • Reviews: Rated 4.8 / 5.0, based on 127 Customer Reviews   ★★★★✯

  • Video Link: YouTube®https://www.youtube.com/watch?v=9bM_iXpp3QE&rel=0

  • Lead-Time (Estimated): Lead time est: tops/covers: 8-11 weeks, 3-4 days for poles/straps from order finalization (as of 11/18/21)

  • PRICE: Pick from Options above!

  • Shipping Notes:
    • Signature required for delivery on orders over $500,
    • Can NOT ship to Post Office (PO) Box,
    • Can NOT change your address after order is placed,
    • Buyer is responsible for all Taxes, Duties and Tariffs imposed by local governments,
    • Use a US48 Based (in Florida, New Jersey or Oregon for example) Freight Forwarder to ship outside the USA or Canadian Provinces,
    • Check shipment for damage upon receipt and file claim with shipper.
Made in USA Paypal Verification Seal
Sales Agreement   |   Privacy Statement  
© 2003-2021, RNR-Marine, Inc.
636G Long Point Road
Mount Pleasant, SC 29464
COMPUTER CCBot/2.0 (https://commoncrawl.org/faq/) US

$Click to pick

Rated 4.5 / 5
based on 111 customer reviews

Scroll down to
select options and purchase...

Made in USA

© 2003-2021, RNR-Marine, Inc.

Page: http://rnr-marine.com/purchase.php?product=Wakeboard-Tower-Over-The-Tower-Boat-Cover-Deck-Boat-C