Carver® p/n 74522S Universal (non-OEM) SunDura® Under-Watersports-Tower Boat Cover for Tournament Ski/Wake Boat, size: 21ft,7in to 22ft,6in CLL, 102-inch BEAM:
Notes:This cover is designed for an 21ft,7in to 22ft,6in CLL, 102-inch BEAM Tournament-Style Ski Boat with WaterSports Tower, Carver® Under-Tower (Tournament Ski Tower TST) Ratchet Boat Covers are available for most Tournament Ski/Wake Boats (Malibu, Mastercraft, Nautique, Correct Craft, Tige, Supra, Centurion, Moomba, etc.) with Watersports Towers. This cover will protect the entire boat from the sun's harmful and damaging UV rays, rain and bird poo:
Velcro-lined Tower Slots on each side accomModate many styles and sizes of watersports towers and fit snugly to keep the boat full protected,
This Trailerable boat cover fits tightly with FREE: (2) Rope Ratchets and (12)each 8-foot Tie-Downs with adjustable snap buckles included,
Sun-DURA® fabric ,
4-Ply join seams (no raw edges),
Strong and durable 1/4" Rope encased in hem for a snug fit,
Double Stitch construction for added strength and durability,
Reinforced at key stress points to reduce wear and prolong cover life,
For clean storage, trailering, mooring and winter storage,
Made-to-order and shipped from Carver® Covers, Inc. in South Carolina, USA.
Size/Fit:
Fits 21ft,7in to 22ft,6in CLL, 102-inch BEAM Tournament-Style Ski Boat with WaterSports Tower
TOWER SLOTS (108 inch long) begin 76-1/2 inches from bow on each side for tower legs (some towers may be too far back or forward, see diagram at right),
Measure and Verify (see drawing and chart at right):
Center Line LENGTH (CLL) from tip of the bow to the back of the boat's fiberglass transom (NOT to the back of a Swim Platform if you have one),
BEAM (boat's width),
Fits tightly under the rub rail all around and does NOT cover Swim Platform,
The cover opens and closes below the Tower Slots and is secured tightly with (2) Rope Ratchets (included) to 1/4" Rope in the Hem,
Tie-Down Loops sewn in the hem every 3-4 feet to secure the cover to your trailer using:
(12)each 8-foot Tie-Down Straps (included) for Trailer storage or
Sand Bags (4 to 10) for Float, Lift or In-Water storage,
Warranty: The materials and workmanship of this products are guaranteed by Carver® to be free of defects at time of manufacture and are covered by the Carver® https://www.carvercovers.com/about-carver/product-warranty-information/ limited warranties: Sunbrella®: 10 years, Sun-Dura™: 7 years, Performance Polyguard®: 5 years. The following will VOID warranty: 1) use of Bungee Cords instead of Tie-Down Straps, 2) use of Boat Cover In-Water (becuase the cover will stay wet). (Product warranties are listed on http://www.rnr-marine.com/Warranty.shtml).
Installation: Cover is rolled and packaged with the bow end of the cover to the outside. The tag on the bow end is sewn into the inside hem of the cover. To cover your boat, start at the bow and work backwards. This cover has tower slots on each side that velcro around your watersport tower legs, and tie tightly closed at the hem on each side with supplied rope ratchets. Detailed installation instructions are included with the cover.
Not what you need? Try
Carver® Under-Tower (Tournament Ski Tower TST) Ratchet Boat Covers are available for most Tournament Ski/Wake Boats (Malibu, Mastercraft, Nautique, Correct Craft, Tige, Supra, Centurion, Moomba, etc.) with Watersports Towers. This cover will protect the entire boat from the sun's harmful and damaging UV rays, rain and bird poo: 
