Purchase
Carver® Styled-To-Fit® Trailerable Boat Cover

Boat-Cover-CSF-Model™Carver(r) Styled-To Fit(tm) boat cover provides a guaranteed fit

Carver® Styled To Fit Boat Cover by Model, Outboard Boat, Port Rear.

Carver® Styled To Fit Boat Covers, Cover Page.

Images (random) of Boat-Cover-CSF-Model
(click images to enlarge).

Not what you need? Try:

• Everything we have for Tahoe 1854 boats... and we have Boat-Cover-CSF-Model for these other boats...

Notes: Styled-To-Fit® boat covers have been made by Carver® in South Carolina, USA for 40+ years:
1. GUARANTEED TO FIT this specific year/make/model boat setup,
2. Offered in three solution dyed fabrics (the threads are made from a dyed material solution, rather than just on the surface, to reduce fading):
  1. Sunbrella® (or Outdura®) 9.25 oz./sq.yd. premium 100% marine grade Acrylic (most fade-proof),
  2. Sun-DURA® 7.6 oz./sq.yd. (600 denier) marine grade Polyester (best value),
  3. Poly-Flex II™ 5.3 oz./sq.yd marine grade Polyester (least expensive),
3. Join seams are folded four-ply (no raw edges) and double-stitched using weather resistant anti-wick thread for added strength and durability,
4. Can be used IN-WATER or drive-on FLOAT as a MOORING COVER with Sand Bags (below), but there are NO openings for lines to your cleats,
5. TRAILERABLE at reasonable highway speeds when cinched tightly with (12) FREE Heavy Duty TIE-DOWN STRAPS (6 on smaller covers) connected to the Sturdy TIE-DOWN-LOOPS (every 3-4 feet, double sewn in an offset "V" for strength),
6. 1/4" Stretch Cord in hem (No Snaps) pulls cover tightly under your rub rail,
7. MOTOR COVER sewn into outboard model boat covers (some use a separate motor cover).
Size/Fit:
- GUARANTEED TO FIT this specific year/make/model boat setup or we will replace it or have it returned for a refund (https://dealerguide.carvercovers.com/mmy/boat),
- Bimini-Tops must be lowered and stored flat or removed (unless stated otherwise),
- Pedestal Seats must be removed or lowered,
- Does NOT FIT THE FOLLOWING UNLESS SPECIFICALLY STATED IN BOAT DESCRIPTION ABOVE: • Other boat models or years (it MAY fit other boats, but we cannot guarantee fit), • Wakeboard Tower, • Folded or Upright Bimini-Top, • Radar Arch, • Camper-Top, • T-Top, • Hard-Top, • Ski Tow Pylon, • Non-Integrated Swim Platform, • Bow or Stern Mounted Trolling Motor, • Raised or protruding antennas, brackets, winches, mirrors, rod holders, etc.,
- Will NOT fit ANY NON-Factory-Installed Arch, Top or Tower because it may be installed in a different location,
- NOT intended for use on a LIFT, as it is difficult (or impossible) to pull the cover back over the transom properly,
- Does NOT have or use Snaps like a factory original Bow, Cockpit or Playpen Cover,
- Ships in a 12x12x19 box weighing approximately the boat's length (E.g.: 22' boat = 22# cover).
Options:
1. Carver® p/n 61001 (12) 8-foot Tie-Down Straps and Mesh Storage Bag (at right, 2 sets required for trailering boats over 20ft),
2. p/n 61010 (4) Sand Bag Kit,
3. p/n 61015 Pontoon Mooring Kit: (8) Sand Bags, (3) Vented Poles,
4. Carver® p/n 60000 + SNAP Anodized Aluminum Support Pole with Snap Patch snaps into 8x8 Adhesive Snap Patch (included),
5. Carver® 8x8 Adhesive Snap Patch to use your existing Snap-Top Pole,
6. Carver® p/n 60002 Vented Anodized Aluminum Support Pole,
7. Carver® p/n 61050 Cover Reinforcement/Repair Kit for added padding (bow, pulpit, anchor roller) or to make repairs,
8. Carver® p/n 640xxA 30-inch Skirts protect colored sides/ graphics on boat from UV damage,
9. Alternatives
  - Carver® Custom-Fit™ Boat-Covers (over 2,000 models),
  - TTopCovers™ Under T-Top/Hard-Top Boat Covers (custom fit),
  - Carver® Over T-Top/Hard-Top Boat Covers,
  - Carver® Over Wakeboard Tower Boat-Covers,
  - Carver® Flats Boat Covers with Poling Platform.
Warranty: The materials and workmanship are guaranteed by Carver® to be free of defects at time of manufacture and are covered by Carver's® https://www.carvercovers.com/about-carver/product-warranty-information/ limited warranties: Sunbrella®/Outdura®: 10 years, Sun-Dura™: 7 years. (Note: The use of Bungee Cords instead of Tie-Down Straps on Boat-Covers will void the warranty).
Installation: Cover is rolled and packaged with the bow end of the cover to the outside. The tag on the bow end is sewn into the inside hem of the cover. Start at the bow and follow these instructions: Carver® Boat Cover Installation Instructions.
Maintenance and Care: Canvas Care and Maintenance
More Info: https://www.carvercovers.com/styled-to-fit-boat-covers/
Reviews: RNR-Marine™ is rated 4.53 / 5.0 based on 149 RNR-Marine™ Customer reviews and 24 Better Business Bureau® reviews
★★★★✬
Video Link: https://www.youtube.com/watch?v=1W4dCGZxxNw&rel=0
Select your boat: