nmf Carver® 14447A Custom-Fit™ Boat Cover for Wahoo® 2100 Offshore With Bow Rails, No T-Top (1988-1995) from RNR-Marine.com™
Purchase Carver® 14447A Custom-Fit™ Trailerable Boat Cover part number [14447A] for Wahoo® 2100 Offshore With Bow Rails, No T-Top (1988-1995)
Carver® Custom Fit Boat Cover, Center Console, Starboard Front.
Carver® Custom Fit Boat Cover, Ski Boat with Tower, Starboard Front.
Images (random) of Boat-Cover-CCF (click images to enlarge).
Not what you need? Try:
• Everything we have for Wahoo 2100 boats... and we have Boat-Cover-CCF for these other boats...
Notes:Custom-Fit™ boat covers have been made by Carver® in South Carolina, USA for 40+ years:
This cover was patterned from this original boat and is CUSTOM FIT and GUARANTEED BY CARVER® TO FIT this specific year/make/model boat setup perfectly per https://dealerguide.carvercovers/mmy/boat,
Offered in two Solution-Dyed, Marine Grade fabrics (the dye goes all the way through the threads rather than just on the surface, to reduce fading):
Sunbrella® or Outdura® 9.25 oz./sq.yd. (approximately 750 denier) premium 100% solution-dyed marine grade Acrylic or
TRAILERABLE at reasonable highway speeds when cinched tightly and tied down,
12 FREE Tie Down Straps (NOT Bungees) connect to TIE-DOWN-LOOPS (every 3-4 feet) double sewn in an offset "V" for strength and less strap twisting,
PADS with SNAPS sewn into inside of cover (2 on most, 1 on smaller covers) for optional Support Poles (below),
DURABLE REINFORCEMENTS SEWN in (not glued) at major wear points for extra durability,
MOTOR COVER included on most outboard models.
Size/Fit:NO RISK! GUARANTEED TO FIT ( per https://dealerguide.carvercovers.com/mmy/boat or we will replace it or arrange for return ) the 1988-1995 Wahoo® 2100 Offshore With Bow Rails, No T-Top,
Fits Standard Integrated Fiberglass Swim Platform (as shown at right),
Heavy duty 1/4-inch CINCH ROPE (Not Elastic Cord) sewn into the hem cinches tightly (can use Rope Ratchet below) around the boat below the rub rail at the following Cinch Locations:
Tower: If the description states that it fits a Factory Tower, then it cinches on the sides at the tower leg cutouts,
Bimini: If the description states that it fits a Bimini-Top, then it will cinch on the sides,
NO Tower or Bimini: If the boat (and cover) does NOT have an OEM Tower or Bimini then it will cinch at the center of the transom under the rub rail (or under swim platform, if so equipped).
For use on a trailer, dry stack or float dock,
Does NOT FIT THE FOLLOWING UNLESS SPECIFICALLY STATED IN BOAT DESCRIPTION: • Other boat models or years (it MAY fit other boats, but we cannot guarantee fit), • Wakeboard Tower, • Folded or Upright Bimini-Top, • Radar Arch, • Camper-Top, • T-Top, • Hard-Top, • Ski Tow Pylon, • Non-Integrated Swim Platform, • Bow or Stern Mounted Trolling Motor, • Raised or protruding antennas, brackets, winches, mirrors, rod holders, etc.,
Will NOT fit ANY NON-Factory-Installed Arch, Top or Tower because it may be installed in a different location,
NOT intended for LIFT use, as it is difficult to pull the cover back over the transom,
NOT intended for IN-WATER, as it does NOT have openings for Mooring Lines, and may hang in the water,
Does NOT have or use Snaps,
Ships in a 12x12x19 box weighing approximately the boat's length (E.g.: 22' boat = 22# cover).
Warranty: The materials and workmanship are guaranteed by Carver® to be free of defects at time of manufacture and are covered by Carver's® https://www.carvercovers.com/about-carver/product-warranty-information/ limited warranties: Sunbrella®/Outdura®: 10 years, Sun-Dura™: 7 years. (Note: The use of Bungee Cords instead of Tie-Down Straps on Boat-Covers will void the warranty).
Installation: Cover is rolled and packaged with the bow end of the cover to the outside. The tag on the bow end is sewn into the inside hem of the cover. Start at the bow and follow these instructions: Carver® Boat-Cover Installation Instructions.
Lead-Time (Estimated): Lead time est: tops/covers: 1-2.5 weeks , 3-4 biz days for poles/straps after order finalization as of 5/31/24.
Shipping Notes: Signature required for delivery on orders over $500. Can NOT ship to Post Office (PO) Box. Can NOT change your address after order is placed. Buyer is responsible for all Taxes, Duties and Tariffs imposed by local governments. Use a US48 Based (in Florida, New Jersey or Oregon for example) Freight Forwarder to ship outside US. Check shipment for damage upon receipt and file claim with shipper.
Not what you need? Try:
Custom-Fit™ boat covers have been made by Carver® in South Carolina, USA for 40+ years:
RNR-Marine™ is rated 4.57 / 5.0
based on 147
RNR-Marine™ Customer reviews
and 23
Better Business Bureau® reviews