1/4" DRAW ROPE sewn into hem (NO Snaps) secures cover tightly under rub rail,
TRAILERABLE when cinched tightly and tied down with 12 FREE Tie Down Straps (NOT Bungees) to TIE-DOWN-LOOPS (every 3-4 feet) double sewn in an offset "V" for strength and less strap twisting,
PADS with SNAPS sewn into inside of cover (2 on most, 1 on smaller covers) for optional Support Poles (below),
DURABLE REINFORCEMENTS SEWN in (not glued) at major wear points for extra durability,
Motor Cover included on most outboard models.
Size/Fit: Fits 2006-2020 Boston Whaler® Tender 110, O/B,
Custom Fit and GUARANTEED TO FIT this specific year/make/model boat,
Will NOT fit other years/makes/models (No returns),
Must remove Pedestal Seats from fishing boats,
Fits Standard Integrated Fiberglass Swim Platform (as shown at right),
Heavy duty 1/4-inch Cinch Rope (Not Elastic Cord) encased in hem cinches tightly around the boat below the rub rail at the following Cinch Locations:
Tower: If the description states that it fits a Factory Tower, then it cinches on the sides at the tower leg cutouts,
Bimini: If the description states that it fits a Bimini-Top, then it will cinch on the sides,
NO Tower or Bimini: If the boat (and cover) does NOT have an OEM Tower or Bimini then it will cinch at the center of the transom under the rub rail (or under swim platform, if so equipped).
Does NOT FIT THE FOLLOWING UNLESS SPECIFICALLY STATED IN BOAT DESCRIPTION: • Other boat models or years (it MAY fit other boats, but we cannot guarantee fit), • Wakeboard Tower, • Folded or Upright Bimini-Top, • Radar Arch, • Camper-Top, • T-Top, • Hard-Top, • Ski Tow Pylon, • Non-Integrated Swim Platform, • Bow or Stern Mounted Trolling Motor, • Raised or protruding antennas, brackets, winches, mirrors, rod holders, etc.,
Will NOT fit ANY NON-Factory-Installed Arch, Top or Tower because it may be installed in a different location,
NOT intended for LIFT use, as it is difficult (or impossible) to pull the cover back over the transom,
NOT intended for IN-WATER use (VOIDs the warranty), as it does NOT have openings for Mooring Lines, and may hang in the water. It is a designed for use on a trailer or dry stack (or float dock),
Does NOT have or use Snaps
Ships in 12 x 12 x 19 box weighing approximately 85% (0.85X) of boat length.
Installation: Cover is rolled and packaged with the bow end of the cover to the outside. The tag on the bow end is sewn into the inside hem of the cover. Start at the bow and follow these instructions: Carver® Boat-Cover Installation Instructions.
Lead-Time (Estimated): Lead time est: tops/covers: 1-2 weeks, 3-4 days for poles/straps from order finalization (as of 5/9/22)
$39.38 Shipping to Continental US48
$177.59 Shipping to HAWAII
$187.06 Shipping to CANADIAN PROVINCES
$FF Shipping to EUROPE
$FF Shipping to AUSTRALIA
Shipping Notes: Signature required for delivery on orders over $500. Can NOT ship to Post Office (PO) Box. Can NOT change your address after order is placed. Buyer is responsible for all Taxes, Duties and Tariffs imposed by local governments. Use a US48 Based (in Florida, New Jersey or Oregon for example) Freight Forwarder to ship outside US. Check shipment for damage upon receipt and file claim with shipper.
We have Carver® Trailerable Custom-Fit Boat Covers for (86) different BOSTON WHALER® boat models, including the boat-cover pattern specifically for 2006-2020 BOSTON WHALER® TENDER 110, O/B (outboard) (NO Raised Bimini)