nmf Carver® 16701A Custom-Fit™ Boat Cover for NauticStar® 223DC dual console With or Without Ski Pylon (2013-2023) from RNR-Marine.com™
Purchase Carver® 16701A Custom-Fit™ Trailerable Boat Cover part number [16701A] for NauticStar® 223DC dual console With or Without Ski Pylon (2013-2023)
Carver® Custom Fit Boat Cover, Center Console, Starboard Front.
Carver® Custom Fit Boat Cover, Ski Boat with Tower, Starboard Front.
Images (random) of Boat-Cover-CCF (click images to enlarge).
Notes:Custom-Fit™ boat covers have been made by Carver® in South Carolina, USA for 40+ years:
These covers are offered in two Solution-Dyed, Marine Grade fabrics (the dye goes all the way through the threads rather than just on the surface, to reduce fading):
Sunbrella® or Outdura® 9.25oz/sq.yd Acrylic or
Sun-DURA® 600-denier, 7.6oz/sq.yd Polyester,
1/4" DRAW ROPE sewn into hem (NO Snaps) secures cover tightly under rub rail,
TRAILERABLE when cinched tightly and tied down with 12 FREE Tie Down Straps (NOT Bungees) to TIE-DOWN-LOOPS (every 3-4 feet) double sewn in an offset "V" for strength and less strap twisting,
PADS with SNAPS sewn into inside of cover (2 on most, 1 on smaller covers) for optional Support Poles (below),
DURABLE REINFORCEMENTS SEWN in (not glued) at major wear points for extra durability,
Motor Cover included on most outboard models.
Size/Fit: Fits 2013-2023 NauticStar® 223DC dual console With or Without Ski Pylon,
Fits Standard Integrated Fiberglass Swim Platform (as shown at right),
Heavy duty 1/4-inch Cinch Rope (Not Elastic Cord) encased in hem cinches tightly around the boat below the rub rail at the following Cinch Locations:
Tower: If the description states that it fits a Factory Tower, then it cinches on the sides at the tower leg cutouts,
Bimini: If the description states that it fits a Bimini-Top, then it will cinch on the sides,
NO Tower or Bimini: If the boat (and cover) does NOT have an OEM Tower or Bimini then it will cinch at the center of the transom under the rub rail (or under swim platform, if so equipped).
For use on a trailer, dry stack or float dock,
Does NOT FIT THE FOLLOWING UNLESS SPECIFICALLY STATED IN BOAT DESCRIPTION: • Other boat models or years (it MAY fit other boats, but we cannot guarantee fit), • Wakeboard Tower, • Folded or Upright Bimini-Top, • Radar Arch, • Camper-Top, • T-Top, • Hard-Top, • Ski Tow Pylon, • Non-Integrated Swim Platform, • Bow or Stern Mounted Trolling Motor, • Raised or protruding antennas, brackets, winches, mirrors, rod holders, etc.,
Will NOT fit ANY NON-Factory-Installed Arch, Top or Tower because it may be installed in a different location,
NOT intended for LIFT use, as it is difficult (or impossible) to pull the cover back over the transom,
NOT intended for IN-WATER, as it does NOT have openings for Mooring Lines, and may hang in the water,
Does NOT have or use Snaps,
Ships in a 12x12x19 box weighing approximately the boat's length (E.g.: 22' boat = 22# cover).
Warranty: The materials and workmanship are guaranteed by Carver® to be free of defects at time of manufacture and are covered by Carver's® https://www.carvercovers.com/about-carver/product-warranty-information/ limited warranties: Sunbrella®/Outdura®: 10 years, Sun-Dura™: 7 years. (Note: The use of Bungee Cords instead of Tie-Down Straps on Boat-Covers will void the warranty).
Installation: Cover is rolled and packaged with the bow end of the cover to the outside. The tag on the bow end is sewn into the inside hem of the cover. Start at the bow and follow these instructions: Carver® Boat-Cover Installation Instructions.
Lead-Time (Estimated): Lead time est: tops/covers: 3-10 biz days , 3-4 biz days for poles/straps after order finalization as of 4/25/24.
Shipping Notes: Signature required for delivery on orders over $500. Can NOT ship to Post Office (PO) Box. Can NOT change your address after order is placed. Buyer is responsible for all Taxes, Duties and Tariffs imposed by local governments. Use a US48 Based (in Florida, New Jersey or Oregon for example) Freight Forwarder to ship outside US. Check shipment for damage upon receipt and file claim with shipper.