Solution-Dyed Fabric choices (meaning the dye color goes all the way through the fabric threads rather than just on the surface, to reduce fading):
Fabrics: Sunbrella® or Outdura® 9.25oz/sq.yd Premium 100% solution-dyed marine grade Acrylic OR Sun-DURA® heavy duty, 600-denier, 7.6oz./sq.yd. solution dyed marine grade Polyester,
Join seams are folded four-ply (no raw edges) and sewn with double-stitches using weather resistant anti-wick thread for added strength and durability,
Tie-Down "V" Loops (every 3-4 feet) double sewn in an offset "V" for strength and less strap twisting to attach Tie-Downs or Sand-Bags (sold below) along bottom edge of cover,
TRAILERABLE when properly installed and tied down with INCLUDED, FREE #61000 (12) Tie-Down Straps (NOT Bungee cords) connected to the "V" Loops,
1/4" Stretch Cord in hem (No Snaps) to pull cover tight under rub rail,
MOTOR COVER sewn into outboard (O/B) model boat covers (some have separate motor cover).
Size/Fit: Fits 2005-2007 Larson® LXi 268 I/O,
V-hull Runabout I/O boat (including Euro-style) with Windshield and Hand or Bow Rails (height: 14-16ft=4-inch, 16-20ft=8-inch, 20ft+=12-inch), sterndrive,
No Tower or Arch; Bimini Lowered; Pedestal Seat(s) Removed
Cover is GUARANTEED TO FIT this specific year/make/model boat setup,
Bimini-Tops must be lowered and stored flat or removed (unless stated otherwise),
Pedestal Seats must be removed or lowered,
Does NOT FIT THE FOLLOWING UNLESS SPECIFICALLY STATED IN BOAT DESCRIPTION: • Other boat models or years (it MAY fit other boats, but we cannot guarantee fit), • Wakeboard Tower, • Folded or Upright Bimini-Top, • Radar Arch, • Camper-Top, • T-Top, • Hard-Top, • Ski Tow Pylon, • Non-Integrated Swim Platform, • Bow or Stern Mounted Trolling Motor, • Raised or protruding antennas, brackets, winches, mirrors, rod holders, etc.,
Will NOT fit ANY NON-Factory-Installed Arch, Top or Tower because it may be installed in a different location,
NOT intended for use on a LIFT, as it is difficult (or impossible) to pull the cover back over the transom properly,
NOT intended for IN-WATER use, which VOIDs the warranty (NO openings for Mooring Lines, and may hang in the water). It is a designed for use on a trailer, dry stack or float dock.,
Does NOT have or use Snaps like a factory original Bow, Cockpit or Playpen Cover,
Ships in a 12 x 12 x 19 box weighing approximately the boat's length (E.g.: 22' boat = 22# cover).
Warranty: The materials and workmanship are guaranteed by Carver® to be free of defects at time of manufacture and are covered by Carver's® https://www.carvercovers.com/about-carver/product-warranty-information/ limited warranties: Sunbrella®/Outdura®: 10 years, Sun-Dura™: 7 years. The following VOIDs warranty: 1) use of Bungee Cords instead of Tie-Down Straps on Boat-Cover, 2) use of Boat-Cover IN Water (because the cover will stay wet).
Installation: Cover is rolled and packaged with the bow end of the cover to the outside. The tag on the bow end is sewn into the inside hem of the cover. Start at the bow and follow these instructions: Carver® Boat Cover Installation Instructions.
Lead-Time (Estimated): Lead time est: tops/covers: 1-1.5 weeks, 2-3 biz days for poles/straps from order finalization (as of 9/22/22)
Shipping Notes: Signature required for delivery on orders over $500. Can NOT ship to Post Office (PO) Box. Can NOT change your address after order is placed. Buyer is responsible for all Taxes, Duties and Tariffs imposed by local governments. Use a US48 Based (in Florida, New Jersey or Oregon for example) Freight Forwarder to ship outside US. Check shipment for damage upon receipt and file claim with shipper.
We have Carver® Styled-To-Fit™ Boat Covers for (222) different LARSON® boat models,
Oops, there was a search error or NO Carver® Styled-To-Fit™ Boat-Covers found for [LARSON] [LXi 268 I/O|2005-2007] (err3)
Please select your boat model and options from our complete list of Carver® Styled-To-Fit™ Boat-Covers: