Notes:Styled-To-Fit™ boat covers have been made by Carver® in South Carolina, USA for 40+ years:
These covers are offered in two Solution-Dyed fabrics (the dye goes all the way through the threads rather than just on the surface, to reduce fading):
Sunbrella® or Outdura® 9.25oz/sq.yd Premium 100% solution-dyed marine grade Acrylic,
Sun-DURA® heavy duty, 600-denier, 7.6oz/sq.yd solution dyed marine grade Polyester,
Join seams are folded four-ply (no raw edges) and sewn with double-stitches using weather resistant anti-wick thread for added strength and durability,
"V" Loops (every 3-4 feet) double sewn in an offset "V" for strength and less strap twisting to attach Tie-Downs or Sand-Bags (sold below) along bottom edge of cover,
Can be used IN-WATER or on a drive-on FLOAT as a MOORING COVER with Sand Bags (below),
TRAILERABLE when properly installed and tied down with INCLUDED: FREE 12 (or 6 on smaller covers) TIE-DOWN STRAPS (NOT Bungee cords),
1/4" Stretch Cord in hem (No Snaps) to pull cover tight under rub rail,
MOTOR COVER sewn into outboard (O/B) model boat covers (some use a separate motor cover).
Size/Fit: Fits 1983-1985 Mirro Craft® Breakaway/Daybreak II 17,
V-hull Runabout O/B boat (including Euro-style) with Windshield and Hand or Bow Rails (height: 14-16ft=4-inch, 16-20ft=8-inch, 20ft+=12-inch); outboard,
No Tower or Arch; No or Lowered Bimini; Pedestal Seat(s) Removed; Motor Cover attached
Bimini-Tops must be lowered and stored flat or removed (unless stated otherwise),
Pedestal Seats must be removed or lowered,
Does NOT FIT THE FOLLOWING UNLESS SPECIFICALLY STATED IN BOAT DESCRIPTION ABOVE: • Other boat models or years (it MAY fit other boats, but we cannot guarantee fit), • Wakeboard Tower, • Folded or Upright Bimini-Top, • Radar Arch, • Camper-Top, • T-Top, • Hard-Top, • Ski Tow Pylon, • Non-Integrated Swim Platform, • Bow or Stern Mounted Trolling Motor, • Raised or protruding antennas, brackets, winches, mirrors, rod holders, etc.,
Will NOT fit ANY NON-Factory-Installed Arch, Top or Tower because it may be installed in a different location,
NOT intended for use on a LIFT, as it is difficult (or impossible) to pull the cover back over the transom properly,
Does NOT have or use Snaps like a factory original Bow, Cockpit or Playpen Cover,
Ships in a 12x12x19 box weighing approximately the boat's length (E.g.: 22' boat = 22# cover).
Warranty: The materials and workmanship are guaranteed by Carver® to be free of defects at time of manufacture and are covered by Carver's® https://www.carvercovers.com/about-carver/product-warranty-information/ limited warranties: Sunbrella®/Outdura®: 10 years, Sun-Dura™: 7 years. (Note: The use of Bungee Cords instead of Tie-Down Straps on Boat-Covers will void the warranty).
Installation: Cover is rolled and packaged with the bow end of the cover to the outside. The tag on the bow end is sewn into the inside hem of the cover. Start at the bow and follow these instructions: Carver® Boat Cover Installation Instructions.
Not what you need? Try:
Styled-To-Fit™ boat covers have been made by Carver® in South Carolina, USA for 40+ years:
Sunbrella® or Outdura® 9.25oz/sq.yd Premium 100% solution-dyed marine grade Acrylic, 
grade Polyester,
(some use a separate motor cover).
RNR-Marine™ is rated 4.57 / 5.0
based on 147
RNR-Marine™ Customer reviews
and 23
Better Business Bureau® reviews