SQL ERROR 4855: NO match for [skeeter|zx 225 dc dual console with trolling motor||2015|2021|] in Boats Table [DB/Boats2.psv]. ... Redirecting to Skeeter.shtml#225 in 5 seconds...
Notes:Styled-To-Fit™ Boat Covers for over 25,000 specific boat models have been manufactured in the USA by Carver® for 40+ years:
Solution-Dyed Fabric choices (meaning the dye color goes all the way through the fabric threads rather than just on the surface, to reduce fading):
Fabrics: Sunbrella® or Outdura® 9.25oz/sq.yd Premium 100% solution-dyed marine grade Acrylic OR Sun-DURA® heavy duty, 600-denier, 7.6oz./sq.yd. solution dyed marine grade Polyester,
Join seams are folded four-ply (no raw edges) and sewn with double-stitches using weather resistant anti-wick thread for added strength and durability,
Tie-Down "V" Loops (every 3-4 feet) double sewn in an offset "V" for strength and less strap twisting to attach Tie-Downs or Sand-Bags (sold below) along bottom edge of cover,
TRAILERABLE when properly installed and tied down with INCLUDED: FREE 12 (or 6 on smaller covers) TIE-DOWN STRAPS (NOT Bungee cords) connected to the "V" Loops,
1/4" Stretch Cord in hem (No Snaps) to pull cover tight under rub rail,
MOTOR COVER sewn into outboard (O/B) model boat covers (some have separate motor cover).
Size/Fit: Fits 2015-2021 Skeeter® ZX 225 DC dual console With Trolling Motor,
Wide V-Hull Fiberglass Bass Boat; O/B,
Covers optional Bow Trolling Motor (LIFT-ASSIST may be too tall), Depth Finders; Pedestal Seats Folded Down or Removed; up to 12-inch Windscreen; Buy Longer Cover for JACK PLATE; No Bimini; Motor Cover attached
Cover is GUARANTEED TO FIT this specific year/make/model boat setup,
Bimini-Tops must be lowered and stored flat or removed (unless stated otherwise),
Pedestal Seats must be removed or lowered,
Does NOT FIT THE FOLLOWING UNLESS SPECIFICALLY STATED IN BOAT DESCRIPTION ABOVE: • Other boat models or years (it MAY fit other boats, but we cannot guarantee fit), • Wakeboard Tower, • Folded or Upright Bimini-Top, • Radar Arch, • Camper-Top, • T-Top, • Hard-Top, • Ski Tow Pylon, • Non-Integrated Swim Platform, • Bow or Stern Mounted Trolling Motor, • Raised or protruding antennas, brackets, winches, mirrors, rod holders, etc.,
Will NOT fit ANY NON-Factory-Installed Arch, Top or Tower because it may be installed in a different location,
NOT intended for use on a LIFT, as it is difficult (or impossible) to pull the cover back over the transom properly,
NOT intended for IN-WATER use, which VOIDs the warranty (NO openings for Mooring Lines, and may hang in the water). It is a designed for use on a trailer, dry stack, float dock or Sea Pen,
Does NOT have or use Snaps like a factory original Bow, Cockpit or Playpen Cover,
Ships in a 12 x 12 x 19 box weighing approximately the boat's length (E.g.: 22' boat = 22# cover).
Warranty: The materials and workmanship are guaranteed by Carver® to be free of defects at time of manufacture and are covered by Carver's® https://www.carvercovers.com/about-carver/product-warranty-information/ limited warranties: Sunbrella®/Outdura®: 10 years, Sun-Dura™: 7 years. The following VOIDs warranty: 1) use of Bungee Cords instead of Tie-Down Straps on Boat-Cover, 2) use of Boat-Cover IN Water (because the cover will stay wet).
Installation: Cover is rolled and packaged with the bow end of the cover to the outside. The tag on the bow end is sewn into the inside hem of the cover. Start at the bow and follow these instructions: Carver® Boat Cover Installation Instructions.
Not what you need? Try:
Styled-To-Fit™ Boat Covers for over 25,000 specific boat models have been manufactured in the USA by Carver® for 40+ years:
Fabrics: Sunbrella® or Outdura® 9.25oz/sq.yd Premium 100% solution-dyed marine grade Acrylic OR Sun-DURA® heavy duty, 600-denier, 7.6oz./sq.yd. solution dyed marine 
grade Polyester,
(some have separate motor cover).
https://www.youtube.com/watch?v=1W4dCGZxxNw&rel=0
RNR-Marine™ is rated 4.78 / 5.0
based on 146
RNR-Marine™ Customer reviews
and 23
Better Business Bureau® reviews