Join seams are folded four-ply (no raw edges) and double-stitched using weather resistant anti-wick thread for added strength and durability,
Can be used IN-WATER or drive-on FLOAT as a MOORING COVER with Sand Bags (below), but there are NO openings for lines to your cleats,
TRAILERABLE at reasonable highway speeds when cinched tightly with (12) FREE Heavy Duty TIE-DOWN STRAPS (6 on smaller covers) connected to the Sturdy TIE-DOWN-LOOPS (every 3-4 feet, double sewn in an offset "V" for strength),
1/4" Stretch Cord in hem (No Snaps) pulls cover tightly under your rub rail,
MOTOR COVER sewn into outboard model boat covers (some use a separate motor cover).
Size/Fit:NO RISK! GUARANTEED TO FIT the 1999 Sylvan® Blue Fish 1700 DC, O/B:
V-hull Runabout O/B boat (including Euro-style) with Windshield and Hand or Bow Rails (height: 14-16ft=4-inch, 16-20ft=8-inch, 20ft+=12-inch); outboard,
No Tower or Arch; No or Lowered Bimini; Pedestal Seat(s) Removed (Motor Cover attached)
Bimini-Tops must be lowered and stored flat or removed (unless stated otherwise),
Pedestal Seats must be removed or lowered,
Does NOT FIT THE FOLLOWING UNLESS SPECIFICALLY STATED IN BOAT DESCRIPTION ABOVE: • Other boat models or years (it MAY fit other boats, but we cannot guarantee fit), • Wakeboard Tower, • Folded or Upright Bimini-Top, • Radar Arch, • Camper-Top, • T-Top, • Hard-Top, • Ski Tow Pylon, • Non-Integrated Swim Platform, • Bow or Stern Mounted Trolling Motor, • Raised or protruding antennas, brackets, winches, mirrors, rod holders, etc.,
Will NOT fit ANY NON-Factory-Installed Arch, Top or Tower because it may be installed in a different location,
NOT intended for use on a LIFT, as it is difficult (or impossible) to pull the cover back over the transom properly,
Does NOT have or use Snaps like a factory original Bow, Cockpit or Playpen Cover,
Ships in a 12x12x19 box weighing approximately the boat's length (E.g.: 22' boat = 22# cover).
Warranty: The materials and workmanship are guaranteed by Carver® to be free of defects at time of manufacture and are covered by Carver's® https://www.carvercovers.com/about-carver/product-warranty-information/ limited warranties: Sunbrella®/Outdura®: 10 years, Sun-Dura™: 7 years. (Note: The use of Bungee Cords instead of Tie-Down Straps on Boat-Covers will void the warranty).
Installation: Cover is rolled and packaged with the bow end of the cover to the outside. The tag on the bow end is sewn into the inside hem of the cover. Start at the bow and follow these instructions: Carver® Boat Cover Installation Instructions.
Lead-Time (Estimated): Lead time est: 1.5-2.5 weeks (Covers, Tops), 4-5 biz days for poles and straps after order finalization as of 9/3/24.
Shipping Notes: Signature required for delivery on orders over $500. Can NOT ship to Post Office (PO) Box. Can NOT change your address after order is placed. Buyer is responsible for all Taxes, Duties and Tariffs imposed by local governments. Use a US48 Based (in Florida, New Jersey or Oregon for example) Freight Forwarder to ship outside US. Check shipment for damage upon receipt and file claim with shipper.
Not what you need? Try:
Styled-To-Fit® boat covers have been made by Carver® in South Carolina, USA for 40+ years:
Join seams are folded four-ply (no raw edges) and double-stitched using weather resistant anti-wick thread for added strength and durability,
(some use a separate motor cover).
RNR-Marine™ is rated 4.53 / 5.0
based on 149
RNR-Marine™ Customer reviews
and 24
Better Business Bureau® reviews